8 Critical Control Valve Selection Criteria

Control Valve (Valtek)
Control Valve (Valtek)
Choosing an improperly applied sized or improperly sized control valve can have serious consequences on operation, productivity and most important, safety. Here is a quick checklist of basics that need to be considered:
  1. Control valves are not intended to be a an isolation valve and should not be used for isolating a process. 
  2. Always carefully select the correct materials of construction. Take into consideration the parts of the valve that comes in to contact with the process media such as the valve body, the seat and any other "wetted" parts. Consider the operating pressure and operating temperature the control valve will see. Finally, also consider the ambient atmosphere and any corrosives that can occur and effect the exterior of the valve. 
  3. Put your flow sensor upstream of the control valve. Locating the flow sensor downstream of the control valve exposes it to an unstable flow stream which is caused by turbulent flow in the valve cavity.
  4. Factor in the degree of control you need and make sure your valve is mechanically capable. Too much dead-band leads to hunting and poor control. Dead-band is roughly defined as the amount of control signal required to affect a change in valve position. It is caused by worn, or loosely fitted mechanical linkages, or as a function of the controller setting. It can also be effected by the tolerances from mechanical sensors, friction inherent in the the valve stems and seats, or from an undersized actuator. 
  5. Consider stiction. The tendency for valves that have had very limited travel, or that haven't moved at all, to "stick" is referred to as stiction. It typically is caused by the valves packing glands, seats or the pressure exerted against the disk. To overcome stiction, additional force needs to be applied by the actuator, which can lead to overshoot and poor control.
  6. Tune your loop controller properly. A poorly tuned controller causes overshoot, undershoot and hunting. Make sure your proportional, integral, and derivative values are set). This is quite easy today using controllers with advanced, precise auto-tuning features that replaced the old fashioned trial and error loop tuning method.
  7. Don't over-size your control valve. Control valves are frequently sized larger than needed for
    Control Valve Specialized Kammer
    Control Valve
    Specialized for Food/Bev
    Pharmaceutical (Kammer)
    the flow loop they control. If the control valve is too large, only a small percentage of travel is used (because a small change in valve position has a large effect on flow), which in turn makes the valve hunt. This causes excessive wear. Try to always size a control valve at about 70%-90% of travel.
  8. Think about the type of control valve you are using and its inherent flow characteristic. Different types of valve, and their disks, have very different flow characteristics (or profiles). The flow characteristic can be generally thought of as the change in rate of flow in relationship to a change in valve position. Globe control valves have linear characteristics which are preferred, while butterfly and gate valves have very non-linear flow characteristics, which can cause control problems. In order to create a linear flow characteristic through a non-linear control valve, manufacturers add specially designed disks or flow orifices which create a desired flow profile.
These are just a few of the more significant criteria to consider when electing a control valve. You should always discuss your application with an experienced application expert before making your final selection.

Consider Flangeless Wafer Style Control Valves for Excellent Flow Control

Mark 75 Flangeless Wafer Style Control Valve
Jordan Mark 75 Flangeless
Wafer Style Control Valve
Valves are essential to industries which constitute the backbone of the modern world. The prevalence of valves in engineering, mechanics, and science demands that each individual valve performs to a certain standard.

One category of valves are "control valves". These can be linearly operated, or rotary operated. There are many types of control valves, such as gate, globe, ball, butterfly, and plug. All of these valve types have some sort of ball, plug, gate, or disc that throttles the flow as the valve opens and closes. Some valve designs are better suited to uniformly control flow, such as gate valves or valves with specially machined disks. This post is about the Jordan Mark 75, a valve that uses a unique sliding gate design.

According to Wikipedia, "A control valve is a valve used to control fluid flow by varying the size of the flow passage as directed by a signal from a controller. This enables the direct control of flow rate and the consequential control of process quantities such as pressure, temperature, and liquid level."

The Mark 75 Series control valve is a industrial process control valve manufactured by Jordan Valve. It's design benefits include the sliding gate seat design, low weight, and compact wafer style body. The Mark 75 offers an incredible pricing advantage in the market place due to its wafer style body.

The stroke length of the Mark 75 is a slightly longer stroke than standard sliding gate valves. This longer stroke enables better turndown. Combined with the capacity of the Mark 75, the increased turndown makes for a great control valve.

Please watch the video below, and see the specification sheet at the bottom for further details. For more information about this valve, or any Jordan Valve product, contact Swanson Flo at 800-288-7926 or visit http://www.swansonflo.com.


Understanding Industrial Rack and Pinion Valve Actuators

Basic concept of rack and pinion gear
Basic concept of
rack and pinion gear.
Valves are essential to industries which constitute the backbone of the modern world. The prevalence of valves in engineering, mechanics, and science demands that each individual valve performs to a certain standard. Just as the valve itself is a key component of a larger system, the valve actuator is as important to the valve as the valve is to the industry in which it functions. Actuators are powered mechanisms that position valves between open and closed states.

Pneumatic rack and pinion actuators utilize air pressure as the motive force which changes the position of a valve.  A rack and pinion actuator is comprised of two opposing pistons, each with its own gear (referred to as the "rack"). The two piston racks are set against a round pinion gear. As pressure increases against one side of each piston, each rack moves linearly against the opposite sides of the pinion gear causing rotational movement. This rotational movement is used to open and close a valve. See the animation above (provided by Wikipedia) below for a visual understanding.

This short video introduces the basic parts and operation of rack and pinion valve actuators to anyone unfamiliar with the device.


Visit http://www.swansonflo.com to learn more about industrial valves, valve actuators, and valve automation.

Pressure Instrument Calibration

Calibration of pressure instruments
Proper pressure instrument calibration is critically
important for safety and quality.
Calibration of pressure instruments in industrial environments requires the establishment of known pressure magnitudes. With a stable input pressure established, the pressure measurement instrument is provided with a referential benchmark that can be used to evaluate instrument output. There are several physical test standards or methods that can be applied to pressure instruments.

A deadweight tester, sometimes called a dead-test calibrator, creates accurately known pressure using precise masses and pistons of a known area. The gauge or pressure instrument is connected to the deadweight tester. The device is comprised of tubes that contain either oil or water, with a primary piston positioned above the liquid and a secondary piston across from the place where the gauge connects to the tester. A mass of a known quantity is placed atop the primary piston, which is perfectly vertical. The earth's gravitational field acts upon the mass atop the piston. The combination results in a known value being applied to the deadweight tester and subsequently allows for calibration of the gauge.
deadweight tester
Deadweight tester (Ashcroft)

Once pressure builds inside the deadweight tester, surpassing the weight of the piston, the piston will rise and float atop the oil. By rotating the mass atop the piston, the piston will rotate inside its cylinder and negate any impact from friction. Developments in technology have led to testers being equipped with hand pumps and bleed valves. The same principles applied to a deadweight tester which uses oil are applied to a pneumatic deadweight tester, where gas pressure suspends the mass atop the cylinder instead of oil or water pressure.

The manometer is another device which establishes a pressure standard to calibrate gauges. Alone, the manometer is simply a U shaped tube connecting a source of fluid pressure to the gauge being calibrated. Pressure applied to the gauge will be indicated by the corresponding heights of the fluid in the columns. If the value of the density of the liquid is a precise, known value, the aforementioned constant of the earth's gravitational field will combine with the applied pressure to permit calibration of the gauge.
Digital Test Gauge
Digital Test Gauge (Ashcroft)

Test instruments which couple with the calibration of pressure transmitters are also instrumental in ensuring correct pressure calibration. Electronic and pneumatic test instruments, along with precise air pressure calibration pumps, enable calibrating a pressure transmitter in place, in the field, or on a lab bench. These portable devices, though, require their own calibration to physical standards with referenced properties. While different devices exist for establishing pressure standards in either high or low pressure environments, the shared standard allows for varying types of instrumentation to exhibit similar performance quality and accomplish the same task.

Contact Swanson Flo for any pressure instrument repair or calibration requirement. Visit http://www.swansonflo.com or call 800-288-7926.

A Proven Actuator Ideal for Valves Requiring Rotary or Linear Movement

Limitorque L120 electric actuator
Limitorque L120 electric actuator.
Whether used with gate valves, globe valves, penstocks or sluice gates, versatile Limitorque L120 Series actuators operate without modification in any rising or non-rising stem application for linear-action valves.

When combined with a Limitorque WG or HBC series quarter-turn gear operator, L120 actuators can also be used to control butterfly, ball and plug valves, as well as damper drives, flop gates or any other device which requires rotary movement.

L120 actuators are specified for use in petrochemical, power generation, and water and waste treatment applications where failure of a single actuator can be extremely costly … even catastrophic.

For more information on Limitorque actuators, visit Swanson Flo's website or call 800-288-7926.

For your convenience, below you will find the Limitorque L120-85 installation and operation manual.


What are purged impulse lines and why are they needed?

Purged impulse lines
Diagram of a purged impulse line implementation.
(image courtesy of Lessons in Industrial Instrumentation
by Tony R. Kuphaldt
)
Purged impulse lines, or sensing lines, allow process transmitters and gauges to maintain operation under potentially adverse process conditions that may impact the operation or accuracy of the instrument. The purging of an impulse line is of particular use when sensing lines may have a high susceptibility to plugging by the process fluid. The line is purged with clean fluid at a constant rate, meaning new fluid is always being introduced into the impulse line. When the purge is properly set, a critical element of successful implementation, the pressure instrument is still able to correctly measure system pressure.

Purging a sensing line will require additional valves and devices to properly control the purge fluid flow and provide for effective maintenance or repair. Because of the increased relative complexity, a purging setup will likely be employed only in cases where other methods of maintaining clear sensor lines and proper instrument operation have been considered and rejected. The impulse line will stay free of sedimentation thanks to the purge fluid, and process fluid contamination of the sensing line is avoided.

One of the most important parts of the purged impulse line system is a restriction, implemented to prevent the pressure instrumentation from sensing the elevated pressure of the purge fluid supply instead of measuring the original process fluid. The purge valve, through which the purge fluid flows, is left partially open instead of fully open. If the restriction does not mitigate the introduction of the purge fluid on the process line, then the flow rate of the purge fluid can adversely impact the process measurement. It is essential that purge flow be regulated in a manner that does not adversely impact the measurement of actual process conditions.

A basic requirement of sensing line purge systems is that the supply of purge fluid needs to be flowing at all times. Additionally, the purge fluid supply pressure must be maintained at a level greater than the process pressure because if the pressure of the purge fluid supply drops below the process pressure, the process fluid will flow into the impulse line. The purge fluid must also not react negatively with or contaminate the process and will be continuously consumed. Generally, purge rates are kept as low as possible, mitigating purge fluid impact on the process measurement and keeping the cost low. A rotameter, which indicates visual flow of the purge fluid, is an item typically paired with purge impulse line systems, and there are many options available for use as purge fluids.

Common gases for purged impulse lines include air, nitrogen, and carbon dioxide. A purge system can be applied to both gas and liquid process systems. Share your process measurement challenges with instrumentation specialists. Combine your own process knowledge and experience with their product application expertise to develop effective solutions.

Fundamentals of Thermal Mass Flow Measurement

Sage Prime Thermal Mass Flow Meter
Thermal Mass Flow Meter
Courtesy of Sage Metering
“Why do we need to measure in mass flow? What is the difference between ACFM and SCFM? Why are pressure and temperature correction not required when measuring with a thermal mass flow meter? What is the thermal mass flow measurement theory? What are common applications to use thermal mass flow meters?” The white paper below attempts to explain these questions and more. 

The original Sage Metering Document titled "Fundamentals of Thermal Mass Flow Measurement" can be downloaded here.